How to Update Audi MMI 3G High & 3G Plus Navigation Maps

Updating navigation maps on Audi MMI 3G High and MMI 3G Plus requires more than simply copying new files to an SD card.
The correct procedure depends on the exact MMI generation, current firmware, navigation region and map package.
This guide is specifically for:
- MMI 3G High - software trains beginning with HNav_
- MMI 3G Plus - software trains beginning with HN+_ or HN+R_
If your software version begins with BNav_, you have MMI 3G Basic and should use our separate MMI 3G Basic map update guide.
If your system uses MHI2, MHI2Q, MHS2, MH2p or MHI3, this is not the correct map installation procedure.
Before starting, identify your exact MMI system and record both the firmware version and navigation database version.
MMI 3G Basic map guide:
https://mmiupdates.com/tutorials/how-to-update-maps-in-mmi-3g-basic/
Audi MMI identification guide:
https://mmiupdates.com/tutorials/how-to-check-what-mmi-do-i-have-mmi-2g-3g-3g-types-of-audi-navigation-systems/
Table of content.
- What MMI do I have?
- What’s my current map version?
- How to get latest maps for my MMI?
- How to enable hidden green menu?
- How to remove old nav database?
- How to unpack files & prepare SD CARDs?
- Map installation.
- How to enable User Defined mode?
- How to activate my maps?
- Audi RSE - Rear Seat Entertainment - how to update?
- COMMON ERRORS LIST AND EXPLANATION.
Check Whether You Have MMI 3G High or MMI 3G Plus
If you already own the maps update files and you are ready to install, you can jump straight to the installation manual by clicking here.
We also have a video tutorial
First of all, you have to recognise which MMI your car have.
The best way it’s just to go to the Engineering menu and check the current firmware version.
You can enter there by pressing the CAR and SETUP (or sometimes MENU or BACK) buttons in your MMI console.
This video might be also useful



When you are in the engineering menu, you will see screen like above.
Most Trans it’s your current MMI version.
There's few different MMI versions.

When you are in Engineering Menu you can now recognise your MMI, so:
- MMI 2G: SW: XX-XX XX.X.X XXXX
- MMI 3G Low/Basic: BNav_XX_XXXXX
- MMI 3G High: HNav_XX_XXXXX
- MMI 3G+: HN+_XX_XXXXX or HN+R
- MMI RMC: RMC_XX_XXXXX
This guide continues only if your software version starts with:
HNav_ = MMI 3G High
HN+_ = MMI 3G Plus
HN+R_ = MMI 3G Plus
If you see BNav_, RMC_, MHI2_, MHI2Q_, MHS2_, MH2p_ or another prefix, stop here and use the installation procedure written for that platform.

Once you know your exact MMI version, check whether your current firmware is compatible with the map release you want to install.
You can verify available firmware and map updates here:
https://mmiupdates.com/check-upgrade/
💡 Sick of outdated factory maps?
Bring your Audi into the modern era! Upgrade your infotainment system with our premium wireless interface and enjoy seamless access to Apple CarPlay and Android Auto directly on your original factory screen.
Upgrade Your Audi Today & Shop NowWhat’s my current map version?
To check your current map version please go to the main MMI menu

Go to: Setup MMI

Scroll down and go to Version information


And here you have your current map version under the Nav. Database version.
The screenshot above shows an example navigation database version. Your version number will depend on the region and map release currently installed.
How to Choose the Correct Maps for MMI 3G High or 3G Plus
MMI 3G High and MMI 3G Plus do not use the same navigation packages.
Always match the map package to:
- the MMI generation,
- the navigation region,
- the current firmware level,
- and the activation method required by that release.
Typical regions include:
- ECE - Europe
- NAR - USA / Canada / Mexico
- ROW - Rest of World
- ME - Middle East
- AU/NZ - Australia / New Zealand
- South Africa
Do not choose a map update only by Audi model or model year.
Two cars of the same model can have completely different MMI systems.
Check compatible updates:
https://mmiupdates.com/check-upgrade/

If you now know what’s your current maps version and type of MMI, you can download maps from here!
But please be careful, because different MMI systems has a different map updates.
If you have MMI 3G PLUS you have to looking for MMI 3G Plus maps, similar for MMI 3G High and Basic. All maps are selling separately on our website.
Important: Verify the Update Package Before Installation
Do not install navigation files from an unknown or unverified source.
A damaged, incomplete or incompatible package can cause the update to fail and may leave the navigation database unusable.
Before installation, confirm that:
- all archive parts were downloaded,
- extraction completed without errors,
- the map package matches your MMI generation,
- the region is correct,
- and the required activation method is compatible with your system.



How to Prepare the SD Card for an MMI 3G Map Update
Map packages may be supplied as a multi-part 7-Zip archive, for example:
maps.7z.001
maps.7z.002
maps.7z.003
maps.7z.004
Download every part and place all files in the same folder.
Start extraction from the .7z.001 file only. 7-Zip will automatically read the remaining parts.
After extraction, copy the contents of the extracted map folder directly to the root of the SD card.
Do not copy the parent folder itself.
When you receive download links from mmiupdates.com to download maps, you will see something like this:

Download one by one!
when you get all files, please unpack only first one 7z.001 with 7zip!

Other files will join automatically!
Extract downloaded files - how to do? Click here - there's a complete guide how to deal with downloaded files.
Format your SD CARD as FAT32.
Copy the root of your maps on the SD card (like picture below).
Preparing the SD Card on macOS
macOS can create additional hidden metadata files such as .DS_Store and resource-fork files.
If you prepare the SD card on a Mac, make sure the card contains only the files required by the update package before inserting it into the MMI.
Windows or a cleanly prepared FAT32 card is generally the simplest option.
When you have unpacked files with maps go inside created folder and you might see something like on the screenshot bellow.
Keep in mind the file list might be different for EU and USA / Canada so do not count the files etc.
and copy all those files directly on to SDCARD, without parent folder like 6.30.1 or 6.19.1 or other name..

Recommended SDCARDs for Map updates we described in F.A.Q here. When you prepared your SD CARD you can jump to the car and follow rest of this manual.
How to remove old nav database?
Optional: Removing the old map is optional. However, is highly recommendable.
Benefits are:
- Possibly avoid the Fault Code 03175 - Invalid Data Set error
- Avoid errors while copying the map (out of size, slow write speed)
- There are no files of the old map into the new map
Open Green Menu (Press CAR and MENU and hold it)
How to enable hidden green menu - tutorial you can find here!

Go to nav/databaseupdate
Select “Delete database (will need reboot)” and click it.

Wait until system removes the data.

When it finished. Reboot your MMI using the 3 buttons

In Audi A8 it's a bif different MMI reboot: big button, upper right silver and tone


User Defined mode
Therefore, it is necessary to push a “User defined mode” installation mode,
- To activate this mode (it’s disabled by default), you must go to the green menu.

GREEN MENU: Press and hold MENU + TEL or MENU + CAR or TONES + CAR, depending on the model.
** Then go to the SWDL section:


Map installation
Install the Navigation Maps
Before continuing:
- confirm that the correct map package is on the SD card,
- make sure the MMI has fully booted,
- ensure stable vehicle voltage,
- and do not remove the SD card during installation.
The map installation can take a long time. The exact duration depends on the map release, region and MMI hardware.
Open “Engineering Menu” by pressing the CAR button and immediately after the BACK button. Hold booth buttons pressed for a few seconds.
The following screen will appear.

Insert the SD card with the map in slot SD 1
Press the “Update” option using the MMI Control Panel.

Scroll down with the big knob and select the source in the menu (SD 1 in our case).

Select the map by pressing the big knob once.

select “User Defined” (remember? we have enabled this).

Go to the menu AUDI_MMI3G_ECE ->in each sub folder set the check box so that in front of all sub-feet Y
- for US and other will be similar AUDI_MM3G_NAR.
- Australia & New Zealand AUDI_MMI3G_AN.
- South Africa Audi_MMO3G_SA.
- Rest Of World AUDI_MMI3G_ROW.
- Middle East AUDI_MMI3G_ME2.
- Europe AUDI_MMI3G_ECE
- Singapore AUDI_MMI3G_SN
Please also make sure that:
- Mapstyles,
- Navipersistence,
- TMCConfig (this might be N/A in USA/Canada/Mexico cars and do not worry if you can't select this!)
are also selected to update.


Manually select the entire item (without bootloader)
In the MMI section AUDI_MMI3G_XXX
XXX - depends on region, can be:
- ECE for Europe,
- ME2 for Middle East,
- NAR for USA / Canada & Mexico
- SA for South Africa
- SM for Singapore
- ROW for Rest of World

Then please go back, and scroll to the bottom.
Press “Start update” and then “Start”.


The installation may take around an hour or longer depending on the navigation package and system.
Allow the process to complete and do not interrupt power.
Device Summary screen is displayed in the subsequent overview screen.

Scroll down and select “Continue“.

Because you don’t have connection to Audi SVM you have to “Cancel documentation” here. This is the reason for ECU ERROR 03276 Please Check Software Version Management in 5F Information Electr.

Cancelling SVM documentation can result in fault code:
03276 - Please Check Software Version Management
This does not mean that the navigation map installation itself failed.
If the error appears, use our dedicated guide:
How to Activate MMI 3G Navigation Maps
Map installation and map activation are two separate stages.
Some MMI 3G map packages require a compatible navigation licence or activation procedure before the newly installed maps can be used normally.
The activation method must match the MMI system, firmware and map release.
Do not use an activation file intended for a different firmware or navigation platform.
Caution: Do NOT insert the SD until MMI has fully booted you can brick your unit!
Caution: Please double check that you’re using the correct license for your firmware, using incorrect activator will result in a bricked (dead) MMI unitFormat your SD in FAT32.


Copy the root of your license in to the clear SD card - it has to be formatted to FAT32!
If you bought maps update from us, the license is in license.zip file.
Make sure that MMI is fully booted - after final reboot!
(press all buttons once RADIO, CAR, NAV, MEDIA, TEL).
Wait until all options are ok (no options in grey) even when all options are ok wait a minute more.
Latest firmware and maps - must be already installed
Insert the SD card into the 1st MMI slot.
Wait for ~ 15 seconds, if everything is done according to the instructions, MMI will show you instructions what to do next. If it doesn't work, eject the SD CARD and try in second slot.
After maps activation you need to fully reboot your mmi. (Please be aware that turning ignition off / on will not reboot MMI!)

Whether activation needs to be repeated depends on the MMI firmware, previous licence state and the map package being installed.
Follow the activation instructions supplied with the specific update rather than assuming that an existing licence will always remain valid.
Audi RSE - Rear Seat Entertainment Map Update
If you own an Audi car with RSE (Rear Seat Entertainment) it also has to be updated, the whole procedure looks the same like for main MMI unit, there are just different buttons combination.

And you can follow rest of installation which looks the same as for front MMI unit. Just keep in mind there's a different buttons combinations.

Can I Use a USB Drive Instead of an SD Card?
On some MMI 3G configurations, USB media can be accessed through a compatible MMI-to-USB interface.
However, SD card installation is the standard method used in this guide.
Use USB only when the hardware and update procedure you are using explicitly support it.
What to Check After the Map Update
After the MMI has rebooted, check:
- the navigation database version,
- GPS position,
- route calculation,
- map rendering,
- voice guidance,
- TMC / traffic information where supported,
- navigation licence status,
- and any new fault codes in module 5F.
Open:
Setup MMI → Version Information
and verify that the new navigation database version is displayed.
If the maps load but become blocked after a few minutes, check the navigation activation before reinstalling the complete map package.




134 comments
Hi I have gone into Media version "HN+_EU_AU3G_P0530 and Nav Database version is 8R0060884AH ECE 5.13.8 does it need update?
Latest available maps for your MMI : ECE 6.27.2 https://mmiupdates.com/product/audi-mmi-3gp-6-27-2-8r0060884fk-latest-audi-maps/ and firmware: K0942: https://mmiupdates.com/product/audi-a4-hn-eu-au3g-k0942-8r0906961fc-latest-firmware-for-3gp-3g/ latest firmware is required for latest maps update, otherwise they will…
So I should update the firmware first then the maps? is that the correct way to do it?
yes
Hello, I have an SQ5 (model 2014) bought from Germany all traffic functions maps are working. Actually I am living outside Europe and found that the navigation system is working anymore ( once you choose a destination it will start calculation and stop). I was wondering if there are maps for North Africa and if I…
Hiya, unfortunately we do not have maps for other regions than Europe.. With B&O we also recommend to skip update for that (it can be unchecked when starting updates)
Hello, Many thanks for your fast answer, How about using GOOGLE MAP? It was working fine in Europe but here I can still get the google maps but itinerary calculation is not working correctly. Are you selling a kind of activation key to activate Google map outside Europe?
Hello, i followed the instructions to update my audi a5 3GP, and i have problem with PSD2 Code error 140, i try new sdcard and still the same. i don’t know what i can do, also i have the last firmware. help me pls.
Hi there, it looks like problem with copied files. If you was using macOS to copy the files please try with windows. If you were on windows when copied the files, please try download again.
Hello, What will happen when I choose STANDARD and not USER-DEFINED type of installation? Marek
Hiya. If you don't have Bose system then nothing. If you have it, then it will get broken. User defined mode is only necessary to disable Bose update.
I do not have BOSE on my Q5 so then it is save to use STANDARD :) Thanks for explanation.
Hi after a successful firmware update (standard as I have no bose), I did also a successful maps update to latest version (using a 64gb sd card on Audi a1 2015). I only have one PROBLEM: after updating maps I don’t have anymore Google Earth option, is greyed out (was working before map upgrade): any idea? Also is…
Hiya please reinstall only GEMMI from firmware update , select everything under gemmi but ONLY APPLICATION, DO NOT SELECT BOOTLOADER!! About GPS location it's normal after update, little ride fixed it :)
All done following your instructions, working again! Now I have to re-apply the green menu fix and I'm done, latest firmware and maps, straightforward process overall.
I'm glad to hear that! :)
So where would I find the activator to copy to the sd card??
same place you toke the maps :)
they call it "license" in the folder structure and in the tutorial they call it "activator" thats a little bit confusing ; )
we will fix that! :)
I have one question - i have no bose system so as in the comments mentioned i choose "standard" method. Do I have still to make the subfolder check AUDI_MMI3G_ECE where i put everything to yes? Or can i click standard and then start the update?
x
double check if subfolders under AUDI_MMI3G_ECE are selected (only application!) to update (Y) if not, then you have to enable user defined mode and follow tutorial.
when i choose standard they are NOT selected by instance. the problem is when i choose standard then its not possible to check the boxes. i did this already with manual update but then i got an error message that something could not be installed
follow tutorial and enable user defined mode. if you will have problems contact us via email.
Worked everything like a charm. No problems whatsoever. The single thing that requires patients is getting inside the bloody Green Menu but it worked. Thank you for your great work and keep it up. Respect!!!
Glad to hear it helps you! =)))
Swapped SDCARD adapter and everything worked out fine. Thank you for the support and for a great product. 5 stars. Keep it going guys.
Everything worked fine. I followed the videos and instructions and no problems. Watched the videos a few times to make sure I understood what to do. Getting the access to the green menu takes a little patience. Great jobs guys, thanks. Let me know when the next update is out.
Hi, thanks a lot for your amazing instruction, successfully upgraded my Firmware.. with no faults.. but when it comes to maps I have a problem, I did it step by step as instruction and it takes almost half an hour to the final reboot. But my nav now shows a message “navigation data is not enabled” Plz help on this
I got the combo for Maps and MI a few days ago. MMI update went without a hitch, the maps update goes through with no errors but when i try to use the GPS, it says no maps data. What could be the problem. I have installed it 6 times so far with the same results. I also sent a message through the contact section…
Hej, I can't see your email, but looks like you have not activated your maps or not selected MMI3G_NAR when installing new maps.
Not sure why you didn't see my message as I sent it through your support section and I received a confirmation email. I definitely selected the the AUDI_MMI3G_NAR option and activated sub options in the secondary options in it as instructed. I also had the Mapstyles, and Navipersistence selected to update. I didn't…
I have a Bang & Olufsen, do I need to do anything special during installation process, I can't see anything in the instructions/video.
like I wrote you in email. NO. Only when you are doing firmware update, in maps update doesn't matter which audio system you got.
Hi, I ran the map installation today. I had removed all the previous maps and map database before starting. It took about 2 hours 40 minutes. I ran the 'Licence' software too. I saw no problems during installation. I did the final reboot, the maps load up and after a few minutes I get a message..."Navigation is…
what firmware version you have? also how did you rebooted MMI? by using 3 buttons combination?
Hi I have entered the green menu and deleted the map database I have downloaded the maps and unzipped. Copied to an SD card which is approx 26.9GB When I select update in the engineering menu the MMI says "The release info could not be read" ?? Help Thanks
Please take a look on FAQ. https://mmiupdates.com/faq/
I have already looked at the FAQs but that doesn`t solve my problem I have unzipped the download correctly Transferred the files to root sd card directory as your screenshot shows
please send us screenshots how the files looks on SDCARD to [email protected]
Email sent - Thanks
Hi, Still no reply to my email ? did you receive it ? Thanks
Good day. I have HNav_US_P0114_D1. At the beginning of the update I have “Device reports error NaviPersistence - script :0 Error code 146 “ I went into the error code and it said “Version 3 was not downloaded . The device is still running version 0 unchanged. “ Please help!!!
Yes, I pressed the 3 buttons to reboot. The Navigation loads up, you can see the maps, you can set a destination, then after a few minutes it says 'blocked'. I've tried both 'activation licences', but still not working.
Hello. The latest map (6.30.1) does not fit on a 32Gb card. Is it possible to leave out a few files? (for MMI 3GP)
Hej, P1001 it's an firmware, latest maps (for today) it's 6.30.1. If you remove any files it will broke update. You need better quality SDCARD. We recommend to use Samsung EVO+ 32GB - we are using them for updates and works well, we have tested Kingston Canvas and there's also not enough space..
Hi guys, finally today we have just updated the firmware (half hour) and the maps (1 and half)...many thanks for the explanations and the videos, all all is up and running without any problem....the next one "the Car Play challenge"??? I have to think about it :) AUDI A5 2015 MMI3Gplus Cheers Juan Ángel
Hej! I'm glad you did it! :) We do have apple carplay & android auto module which will fit your car: https://mmiupdates.com/product/wireless-carplay-wireless-android-auto-interface-for-audi-cars-with-3g-3g-mib-mmi/ and how to install:…
I completed my purchase and downloaded the firmware but when I try to download the map files, it takes me to a page full of script and doesn't prompt me to save the file like the firmware.
Sign in or create an account to leave a comment →